![]() This section references criteria in Appendix A that the qualified person may consult when designing scaffolds to meet capacity requirements.The standard distinguishes between supported scaffolds (paragraph 1926.451(c)) and suspension scaffolds (paragraph 1926.451(d)).Section 1926.451 sets general requirements that apply to all scaffolds, with variations for some specific types of scaffolds or work situations.Paragraph (b) of 1926.450 provides definitions for particular terms used in Subpart L.The standards applicable to aerial lifts are set out exclusively in 1926.453.Paragraph (a) of 1926.450 states that this standard does not apply to Crane- or Derrick-Suspended Personnel Platforms.Any questions involving enforcement, including compliance concerns raised by employers, should be promptly reported to the Office of Construction Standards and Compliance Assistance at (202) 219-7207.Where provisions of Subpart L are intended to cover only one type of scaffold, the final rule makes that clear. This rule establishes one set of requirements which is applicable to all scaffolds used in construction, except that 1926.451 does not apply to aerial lifts (covered by 1926.453). The final rule resolves many issues raised in earlier attempts to regulate this activity within the construction industry.Many of the revisions made to the proposal reflect recommendations from ACCSH and from other interested parties. ![]() Proposed Subpart L was reviewed by the Advisory Committee on Construction Safety and Health (ACCSH).The comment period was extended or reopened several times (most recently closing on March 18, 1994) and OSHA convened an informal public hearing on Ma(53 FR 2048, January 26, 1988). On November 25, 1986, OSHA issued a notice of proposed rulemaking on scaffolds (51 FR 4268).The Occupational Safety and Health Administration has issued a revised standard for Scaffolds Used in the Construction Industry (Subpart L to ). 1926.453(a)(2) will not take effect until an OMB control number will have been received and displayed for this "collection of information." The National Office will inform the Regional Administrators when clearance is received. Effective Date., The effective date for the Scaffold Standard is November 29, 1996, exc1.The Regional Administrator shall review policies, instruction and guidelines issued by the State to determine that this change has been communicated to the State.The State's acknowledgment of the Plan Changes Two-Way Memorandum may fulfill the plan supplement requirement if the appropriate documentation is provided.The State plan supplement should be in the form of a State directive or policy/procedure document, which details procedures for implementing the safety guidelines in the State.Ensure that State designees submit a plan supplement in accordance with OSHA Instruction STP 2.22A, CH-3, as appropriate, following the established schedule that is agreed upon by the State and Regional Administrator to submit non-field Operations Manual/OSHA Technical Manual Federal program changes.This acknowledgment must include a statement indicating whether the State will follow the guidelines in this instruction or develop alternative guidance. Ensure that the State designees acknowledge receipt of this Federal program change in writing to the Regional Administrator when the State's intention is known, but not later than 70 calendar days after the issuance (10 days for mailing and 60 days for response).Explain to each State designee as requested the technical content of the change and the State designee as requested.Ensure that this change is promptly forwarded to each State designee using a format consistent with the Plan Change Two-way Memorandum in Appendix P, OSHA Instruction STP 2.22A, State Plans Policies and Procedures Manual (SPM).This instruction describes a Federal program change which affects State programs. Regional Administrators and Area Directors shall ensure that the guidelines in this instruction are followed and that compliance officers are familiar with the contents of the standard. OSHA Instruction STD 3-14.1, October 30, 1978, Citation Policy - Specific Scaffold Requirements, is canceled, as are all interpretations issued prior to this date which are in conflict with the standard or the directive. 170, August 29, 1996, pages 46026 - 46131, Safety Standards for Scaffolds Used in the Construction Industry. OSHA Instruction CPL 2.103, the Field Inspection Reference Manual (FIRM).Construction Safety and Health Standards, Subpart L.This instruction establishes inspection procedures and provides clarification to ensure uniform enforcement of the scaffold standards for construction. SUBJECT: Inspection Procedures for Enforcing Subpart L, Scaffolds Used in Construction.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |